20% Off MSRP

Schlage M490 Electromagnetic Lock, 1500lbs.

$853.60 ~~$1,067.00~~

Overview

All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M490 is tested and certified to meet or exceed UL1034 and BHMA 1500 lb hold force requirements.

Standard Features:
• 1500lbs Holding Force
• Bayonet mount makes installation simpler by not requiring magnet to be held overhead while mounting screws are installed
• Field selectable 12/24VDC
• New design allows for RH/LH configuration in the field
• Armature mount allows armature to pivot, compensating for slight opening imperfections
• UL1034 burglary-resistant electronic locking mechanisms, UL10C positive pressure fire tests of door assemblies and ANSI/BHMA Grade 1 certifications
• Automatic Voltage Selection (AVS) senses the voltage applied to the lock and responds accordingly
• Limited lifetime warranty

The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind, to be robust, easy-to-install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing, as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application.

Standard Features

1500lbs Holding Force
Bayonet mount makes installation simpler by not requiring magnet to be held overhead while mounting screws are installed
Field selectable 12/24VDC
New design allows for RH/LH configuration in the field
Armature mount allows armature to pivot, compensating for slight opening imperfections
UL1034 burglary-resistant electronic locking mechanisms, UL10C positive pressure fire tests of door assemblies and ANSI/BHMA Grade 1 certifications
Automatic Voltage Selection (AVS) senses the voltage applied to the lock and responds accordingly
Limited lifetime warranty

Mechanical Specifications

Holding Force: 1500lb
Lock: 12.5 inches L x 3 inches H x 1-3/4 inches W

Eletrical Specifications

Voltage: 12/24VDC
Current: .65A @ 12VDC; .35A @ 24VDC

Models

M490: Base Model
M490P: With Magnetic Bond Sensor, Door Position Switch, and Relock Time Delay

Also Known As

LOC100M490, LOCKNETICS-M490

Finish

Aluminum

Manufacturer

Schlage

Manufacturer Warranty

Lifetime

Model Number

M490

Power Requirements

24VDC/12VDC

Status Monitor

Optional

UPC Code

129122212709

CAD PDF

Datasheet PDF

Installation PDF

Template PDF

2 Questions asked on Schlage M490 Electromagnetic Lock, 1500lbs. • Ask a Question

Q Douglas Bierschenk • 01/29/2021, 7:15:46 AM M490P replaced from customer site due to an intermittent failure. Fault found after bench testing to be an defect in the +V terminal connector in the terminal strip on the printed circuit board. Is this circuit board available as a replacement part? If yes, how can we order a replacement?

A 01/29/2021, 1:15:35 PM Yes, these boards are available separately. Please search part# P44488492 for the replacement circuit board for the M420P/M450P/M490P maglocks by Schlage

Q alfred • 12/18/2023, 5:58:06 AM Hi , im looking at the circuitry of maglock but observed that the NC/NO of the Lock status relay is not activating . Are there any jumper wires that i need to confiure before these can work ? I am trying to use this signal to control my air curtains installed on top of our laboratory door. Kindly advice

A 12/19/2023, 1:03:05 PM No, there are no jumper settings that need to be configured. The MBS (magnetic bond sensor) wires need to be plugged into the main circuit board and the relay should cycle once the lock is considered to be locked & bonded with the metal armature plate. For this condition to be met, the armature plate must make a complete flush connection with the face of the magnetic lock. A partial or weak connection would not be considered fully "bonded" and the relay will not cycle.